This module provides an interface to a Bluetooth controller on a board. Currently this supports Bluetooth Low Energy (BLE) in Central, Peripheral, Broadcaster, and Observer roles, as well as GATT Server and Client and L2CAP connection-oriented-channels. A device may operate in multiple roles concurrently. Pairing (and bonding) is supported on some ports.
This API is intended to match the low-level Bluetooth protocol and provide building-blocks for higher-level abstractions such as specific device types.
This module is still under development and its classes, functions, methods and constants are subject to change.
class BLE ¶
active( [ active , ] / ) ¶
Optionally changes the active state of the BLE radio, and returns the current state.
The radio must be made active before using any other methods on this class.
config( 'param' , / ) ¶
config( * , param=value , ... )
Get or set configuration values of the BLE interface. To get a value the parameter name should be quoted as a string, and just one parameter is queried at a time. To set values use the keyword syntax, and one ore more parameter can be set at a time.
Currently supported values are:
'mac': The current address in use, depending on the current address mode. This returns a tuple of
gatts_writefor details about address type.
This may only be queried while the interface is currently active.
'addr_mode': Sets the address mode. Values can be:
0x00 - PUBLIC - Use the controller’s public address.
0x01 - RANDOM - Use a generated static address.
0x02 - RPA - Use resolvable private addresses.
0x03 - NRPA - Use non-resolvable private addresses.
By default the interface mode will use a PUBLIC address if available, otherwise it will use a RANDOM address.
'gap_name': Get/set the GAP device name used by service 0x1800, characteristic 0x2a00. This can be set at any time and changed multiple times.
'rxbuf': Get/set the size in bytes of the internal buffer used to store incoming events. This buffer is global to the entire BLE driver and so handles incoming data for all events, including all characteristics. Increasing this allows better handling of bursty incoming data (for example scan results) and the ability to receive larger characteristic values.
'mtu': Get/set the MTU that will be used during a ATT MTU exchange. The resulting MTU will be the minimum of this and the remote device’s MTU. ATT MTU exchange will not happen automatically (unless the remote device initiates it), and must be manually initiated with
_IRQ_MTU_EXCHANGEDevent to discover the MTU for a given connection.
'bond': Sets whether bonding will be enabled during pairing. When enabled, pairing requests will set the “bond” flag and the keys will be stored by both devices.
'mitm': Sets whether MITM-protection is required for pairing.
'io': Sets the I/O capabilities of this device.
Available options are:
_IO_CAPABILITY_DISPLAY_ONLY = const(0) _IO_CAPABILITY_DISPLAY_YESNO = const(1) _IO_CAPABILITY_KEYBOARD_ONLY = const(2) _IO_CAPABILITY_NO_INPUT_OUTPUT = const(3) _IO_CAPABILITY_KEYBOARD_DISPLAY = const(4)
'le_secure': Sets whether “LE Secure” pairing is required. Default is false (i.e. allow “Legacy Pairing”).
irq( handler , / ) ¶
Registers a callback for events from the BLE stack. The handler takes two arguments,
event(which will be one of the codes below) and
data(which is an event-specific tuple of values).
注意： As an optimisation to prevent unnecessary allocations, the
uuidentries in the tuples are read-only memoryview instances pointing to
bluetooth’s internal ringbuffer, and are only valid during the invocation of the IRQ handler function. If your program needs to save one of these values to access after the IRQ handler has returned (e.g. by saving it in a class instance or global variable), then it needs to take a copy of the data, either by using
bluetooth.UUID(), like this:
connected_addr = bytes(addr) # equivalently: adv_data, char_data, or notify_data matched_uuid = bluetooth.UUID(uuid)
For example, the IRQ handler for a scan result might inspect the
adv_datato decide if it’s the correct device, and only then copy the address data to be used elsewhere in the program. And to print data from within the IRQ handler,
print(bytes(addr))will be needed.
An event handler showing all possible events:
def bt_irq(event, data): if event == _IRQ_CENTRAL_CONNECT: # A central has connected to this peripheral. conn_handle, addr_type, addr = data elif event == _IRQ_CENTRAL_DISCONNECT: # A central has disconnected from this peripheral. conn_handle, addr_type, addr = data elif event == _IRQ_GATTS_WRITE: # A client has written to this characteristic or descriptor. conn_handle, attr_handle = data elif event == _IRQ_GATTS_READ_REQUEST: # A client has issued a read. Note: this is only supported on STM32. # Return a non-zero integer to deny the read (see below), or zero (or None) # to accept the read. conn_handle, attr_handle = data elif event == _IRQ_SCAN_RESULT: # A single scan result. addr_type, addr, adv_type, rssi, adv_data = data elif event == _IRQ_SCAN_DONE: # Scan duration finished or manually stopped. pass elif event == _IRQ_PERIPHERAL_CONNECT: # A successful gap_connect(). conn_handle, addr_type, addr = data elif event == _IRQ_PERIPHERAL_DISCONNECT: # Connected peripheral has disconnected. conn_handle, addr_type, addr = data elif event == _IRQ_GATTC_SERVICE_RESULT: # Called for each service found by gattc_discover_services(). conn_handle, start_handle, end_handle, uuid = data elif event == _IRQ_GATTC_SERVICE_DONE: # Called once service discovery is complete. # Note: Status will be zero on success, implementation-specific value otherwise. conn_handle, status = data elif event == _IRQ_GATTC_CHARACTERISTIC_RESULT: # Called for each characteristic found by gattc_discover_services(). conn_handle, def_handle, value_handle, properties, uuid = data elif event == _IRQ_GATTC_CHARACTERISTIC_DONE: # Called once service discovery is complete. # Note: Status will be zero on success, implementation-specific value otherwise. conn_handle, status = data elif event == _IRQ_GATTC_DESCRIPTOR_RESULT: # Called for each descriptor found by gattc_discover_descriptors(). conn_handle, dsc_handle, uuid = data elif event == _IRQ_GATTC_DESCRIPTOR_DONE: # Called once service discovery is complete. # Note: Status will be zero on success, implementation-specific value otherwise. conn_handle, status = data elif event == _IRQ_GATTC_READ_RESULT: # A gattc_read() has completed. conn_handle, value_handle, char_data = data elif event == _IRQ_GATTC_READ_DONE: # A gattc_read() has completed. # Note: The value_handle will be zero on btstack (but present on NimBLE). # Note: Status will be zero on success, implementation-specific value otherwise. conn_handle, value_handle, status = data elif event == _IRQ_GATTC_WRITE_DONE: # A gattc_write() has completed. # Note: The value_handle will be zero on btstack (but present on NimBLE). # Note: Status will be zero on success, implementation-specific value otherwise. conn_handle, value_handle, status = data elif event == _IRQ_GATTC_NOTIFY: # A server has sent a notify request. conn_handle, value_handle, notify_data = data elif event == _IRQ_GATTC_INDICATE: # A server has sent an indicate request. conn_handle, value_handle, notify_data = data elif event == _IRQ_GATTS_INDICATE_DONE: # A client has acknowledged the indication. # Note: Status will be zero on successful acknowledgment, implementation-specific value otherwise. conn_handle, value_handle, status = data elif event == _IRQ_MTU_EXCHANGED: # ATT MTU exchange complete (either initiated by us or the remote device). conn_handle, mtu = data elif event == _IRQ_L2CAP_ACCEPT: # A new channel has been accepted. # Return a non-zero integer to reject the connection, or zero (or None) to accept. conn_handle, cid, psm, our_mtu, peer_mtu = data elif event == _IRQ_L2CAP_CONNECT: # A new channel is now connected (either as a result of connecting or accepting). conn_handle, cid, psm, our_mtu, peer_mtu = data elif event == _IRQ_L2CAP_DISCONNECT: # Existing channel has disconnected (status is zero), or a connection attempt failed (non-zero status). conn_handle, cid, psm, status = data elif event == _IRQ_L2CAP_RECV: # New data is available on the channel. Use l2cap_recvinto to read. conn_handle, cid = data elif event == _IRQ_L2CAP_SEND_READY: # A previous l2cap_send that returned False has now completed and the channel is ready to send again. # If status is non-zero, then the transmit buffer overflowed and the application should re-send the data. conn_handle, cid, status = data elif event == _IRQ_CONNECTION_UPDATE: # The remote device has updated connection parameters. conn_handle, conn_interval, conn_latency, supervision_timeout, status = data elif event == _IRQ_ENCRYPTION_UPDATE: # The encryption state has changed (likely as a result of pairing or bonding). conn_handle, encrypted, authenticated, bonded, key_size = data elif event == _IRQ_GET_SECRET: # Return a stored secret. # If key is None, return the index'th value of this sec_type. # Otherwise return the corresponding value for this sec_type and key. sec_type, index, key = data return value elif event == _IRQ_SET_SECRET: # Save a secret to the store for this sec_type and key. sec_type, key, value = data return True elif event == _IRQ_PASSKEY_ACTION: # Respond to a passkey request during pairing. # See gap_passkey() for details. # action will be an action that is compatible with the configured "io" config. # passkey will be non-zero if action is "numeric comparison". conn_handle, action, passkey = data
The event codes are:
from micropython import const _IRQ_CENTRAL_CONNECT = const(1) _IRQ_CENTRAL_DISCONNECT = const(2) _IRQ_GATTS_WRITE = const(3) _IRQ_GATTS_READ_REQUEST = const(4) _IRQ_SCAN_RESULT = const(5) _IRQ_SCAN_DONE = const(6) _IRQ_PERIPHERAL_CONNECT = const(7) _IRQ_PERIPHERAL_DISCONNECT = const(8) _IRQ_GATTC_SERVICE_RESULT = const(9) _IRQ_GATTC_SERVICE_DONE = const(10) _IRQ_GATTC_CHARACTERISTIC_RESULT = const(11) _IRQ_GATTC_CHARACTERISTIC_DONE = const(12) _IRQ_GATTC_DESCRIPTOR_RESULT = const(13) _IRQ_GATTC_DESCRIPTOR_DONE = const(14) _IRQ_GATTC_READ_RESULT = const(15) _IRQ_GATTC_READ_DONE = const(16) _IRQ_GATTC_WRITE_DONE = const(17) _IRQ_GATTC_NOTIFY = const(18) _IRQ_GATTC_INDICATE = const(19) _IRQ_GATTS_INDICATE_DONE = const(20) _IRQ_MTU_EXCHANGED = const(21) _IRQ_L2CAP_ACCEPT = const(22) _IRQ_L2CAP_CONNECT = const(23) _IRQ_L2CAP_DISCONNECT = const(24) _IRQ_L2CAP_RECV = const(25) _IRQ_L2CAP_SEND_READY = const(26) _IRQ_CONNECTION_UPDATE = const(27) _IRQ_ENCRYPTION_UPDATE = const(28) _IRQ_GET_SECRET = const(29) _IRQ_SET_SECRET = const(30)
event, the available return codes are:
_GATTS_NO_ERROR = const(0x00) _GATTS_ERROR_READ_NOT_PERMITTED = const(0x02) _GATTS_ERROR_WRITE_NOT_PERMITTED = const(0x03) _GATTS_ERROR_INSUFFICIENT_AUTHENTICATION = const(0x05) _GATTS_ERROR_INSUFFICIENT_AUTHORIZATION = const(0x08) _GATTS_ERROR_INSUFFICIENT_ENCRYPTION = const(0x0f)
event, the available actions are:
_PASSKEY_ACTION_NONE = const(0) _PASSKEY_ACTION_INPUT = const(2) _PASSKEY_ACTION_DISPLAY = const(3) _PASSKEY_ACTION_NUMERIC_COMPARISON = const(4)
In order to save space in the firmware, these constants are not included on the
module. Add the ones that you need from the list above to your program.
Broadcaster Role (Advertiser) ¶
gap_advertise( interval_us , adv_data = None , * , resp_data = None , connectable = True ) ¶
Starts advertising at the specified interval (in micro seconds). This interval will be rounded down to the nearest 625us. To stop advertising, set interval_us to
adv_data and resp_data can be any type that implements the buffer protocol (e.g.
str). adv_data is included in all broadcasts, and resp_data is send in reply to an active scan.
注意： if adv_data (或 resp_data ) is
None, then the data passed to the previous call to
gap_advertisewill be re-used. This allows a broadcaster to resume advertising with just
gap_advertise(interval_us). To clear the advertising payload pass an empty
Observer Role (Scanner) ¶
gap_scan( duration_ms , interval_us=1280000 , window_us=11250 , active=False , / ) ¶
Run a scan operation lasting for the specified duration (in milli seconds).
To scan indefinitely, set duration_ms to
To stop scanning, set duration_ms to
使用 interval_us and window_us to optionally configure the duty cycle. The scanner will run for window_us micro seconds every interval_us micro seconds for a total of duration_ms milli seconds. The default interval and window are 1.28 seconds and 11.25 milliseconds respectively (background scanning).
For each scan result the
_IRQ_SCAN_RESULTevent will be raised, with event data
(addr_type, addr, adv_type, rssi, adv_data).
addr_typevalues indicate public or random addresses:
0x00 - PUBLIC
0x01 - RANDOM (either static, RPA, or NRPA, the type is encoded in the address itself)
adv_typevalues correspond to the Bluetooth Specification:
0x00 - ADV_IND - connectable and scannable undirected advertising
0x01 - ADV_DIRECT_IND - connectable directed advertising
0x02 - ADV_SCAN_IND - scannable undirected advertising
0x03 - ADV_NONCONN_IND - non-connectable undirected advertising
0x04 - SCAN_RSP - scan response
activecan be set
Trueif you want to receive scan responses in the results.
When scanning is stopped (either due to the duration finishing or when explicitly stopped), the
_IRQ_SCAN_DONEevent will be raised.
Central Role ¶
A central device can connect to peripherals that it has discovered using the observer role (see
) or with a known address.
Peripheral Role ¶
A peripheral device is expected to send connectable advertisements (see
). It will usually be acting as a GATT server, having first registered services and characteristics using
When a central connects, the
event will be raised.
Central & Peripheral Roles ¶
gap_disconnect( conn_handle , / ) ¶
Disconnect the specified connection handle. This can either be a central that has connected to this device (if acting as a peripheral) or a peripheral that was previously connected to by this device (if acting as a central).
On success, the
_IRQ_CENTRAL_DISCONNECTevent will be raised.
Falseif the connection handle wasn’t connected, and
GATT Server ¶
A GATT server has a set of registered services. Each service may contain characteristics, which each have a value. Characteristics can also contain descriptors, which themselves have values.
These values are stored locally, and are accessed by their “value handle” which is generated during service registration. They can also be read from or written to by a remote client device. Additionally, a server can “notify” a characteristic to a connected client via a connection handle.
A device in either central or peripheral roles may function as a GATT server, however in most cases it will be more common for a peripheral device to act as the server.
Characteristics and descriptors have a default maximum size of 20 bytes. Anything written to them by a client will be truncated to this length. However, any local write will increase the maximum size, so if you want to allow larger writes from a client to a given characteristic, use
after registration. e.g.
gatts_register_services( services_definition , / ) ¶
Configures the server with the specified services, replacing any existing services.
services_definition is a list of services , where each service is a two-element tuple containing a UUID and a list of characteristics .
每个 characteristic is a two-or-three-element tuple containing a UUID, a flags value, and optionally a list of descriptors .
每个 descriptor is a two-element tuple containing a UUID and a flags 值。
flags are a bitwise-OR combination of the flags defined below. These set both the behaviour of the characteristic (or descriptor) as well as the security and privacy requirements.
The return value is a list (one element per service) of tuples (each element is a value handle). Characteristics and descriptor handles are flattened into the same tuple, in the order that they are defined.
The following example registers two services (Heart Rate, and Nordic UART):
HR_UUID = bluetooth.UUID(0x180D) HR_CHAR = (bluetooth.UUID(0x2A37), bluetooth.FLAG_READ | bluetooth.FLAG_NOTIFY,) HR_SERVICE = (HR_UUID, (HR_CHAR,),) UART_UUID = bluetooth.UUID('6E400001-B5A3-F393-E0A9-E50E24DCCA9E') UART_TX = (bluetooth.UUID('6E400003-B5A3-F393-E0A9-E50E24DCCA9E'), bluetooth.FLAG_READ | bluetooth.FLAG_NOTIFY,) UART_RX = (bluetooth.UUID('6E400002-B5A3-F393-E0A9-E50E24DCCA9E'), bluetooth.FLAG_WRITE,) UART_SERVICE = (UART_UUID, (UART_TX, UART_RX,),) SERVICES = (HR_SERVICE, UART_SERVICE,) ( (hr,), (tx, rx,), ) = bt.gatts_register_services(SERVICES)
注意： Advertising must be stopped before registering services.
Available flags for characteristics and descriptors are:
from micropython import const _FLAG_BROADCAST = const(0x0001) _FLAG_READ = const(0x0002) _FLAG_WRITE_NO_RESPONSE = const(0x0004) _FLAG_WRITE = const(0x0008) _FLAG_NOTIFY = const(0x0010) _FLAG_INDICATE = const(0x0020) _FLAG_AUTHENTICATED_SIGNED_WRITE = const(0x0040) _FLAG_AUX_WRITE = const(0x0100) _FLAG_READ_ENCRYPTED = const(0x0200) _FLAG_READ_AUTHENTICATED = const(0x0400) _FLAG_READ_AUTHORIZED = const(0x0800) _FLAG_WRITE_ENCRYPTED = const(0x1000) _FLAG_WRITE_AUTHENTICATED = const(0x2000) _FLAG_WRITE_AUTHORIZED = const(0x4000)
As for the IRQs above, any required constants should be added to your Python code.
gatts_read( value_handle , / ) ¶
Reads the local value for this handle (which has either been written by
gatts_writeor by a remote client).
gatts_write( value_handle , data , send_update=False , / ) ¶
Writes the local value for this handle, which can be read by a client.
若 send_update is
True, then any subscribed clients will be notified (or indicated, depending on what they’re subscribed to and which operations the characteristic supports) about this write.
gatts_notify( conn_handle , value_handle , data=None , / ) ¶
Sends a notification request to a connected client.
若 data 不是
None, then that value is sent to the client as part of the notification. The local value will not be modified.
Otherwise, if data is
None, then the current local value (as set with
gatts_write) will be sent.
注意： The notification will be sent regardless of the subscription status of the client to this characteristic.
gatts_indicate( conn_handle , value_handle , / ) ¶
Sends an indication request containing the characteristic’s current value to a connected client.
On acknowledgment (or failure, e.g. timeout), the
_IRQ_GATTS_INDICATE_DONEevent will be raised.
注意： The indication will be sent regardless of the subscription status of the client to this characteristic.
gatts_set_buffer( value_handle , len , append=False , / ) ¶
Sets the internal buffer size for a value in bytes. This will limit the largest possible write that can be received. The default is 20.
设置 append to
Truewill make all remote writes append to, rather than replace, the current value. At most len bytes can be buffered in this way. When you use
gatts_read, the value will be cleared after reading. This feature is useful when implementing something like the Nordic UART Service.
GATT Client ¶
A GATT client can discover and read/write characteristics on a remote GATT server.
It is more common for a central role device to act as the GATT client, however it’s also possible for a peripheral to act as a client in order to discover information about the central that has connected to it (e.g. to read the device name from the device information service).
gattc_discover_services( conn_handle , uuid=None , / ) ¶
Query a connected server for its services.
Optionally specify a service uuid to query for that service only.
For each service discovered, the
_IRQ_GATTC_SERVICE_RESULTevent will be raised, followed by
gattc_discover_characteristics( conn_handle , start_handle , end_handle , uuid=None , / ) ¶
Query a connected server for characteristics in the specified range.
Optionally specify a characteristic uuid to query for that characteristic only.
end_handle=0xffffto search for a characteristic in any service.
For each characteristic discovered, the
_IRQ_GATTC_CHARACTERISTIC_RESULTevent will be raised, followed by
gattc_discover_descriptors( conn_handle , start_handle , end_handle , / ) ¶
Query a connected server for descriptors in the specified range.
For each descriptor discovered, the
_IRQ_GATTC_DESCRIPTOR_RESULTevent will be raised, followed by
gattc_read( conn_handle , value_handle , / ) ¶
Issue a remote read to a connected server for the specified characteristic or descriptor handle.
When a value is available, the
_IRQ_GATTC_READ_RESULTevent will be raised. Additionally, the
gattc_write( conn_handle , value_handle , data , mode=0 , / ) ¶
Issue a remote write to a connected server for the specified characteristic or descriptor handle.
自变量 mode specifies the write behaviour, with the currently supported values being:
mode=0(default) is a write-without-response: the write will be sent to the remote server but no confirmation will be returned, and no event will be raised.
mode=1is a write-with-response: the remote server is requested to send a response/acknowledgement that it received the data.
If a response is received from the remote server the
_IRQ_GATTC_WRITE_DONEevent will be raised.
gattc_exchange_mtu( conn_handle , / ) ¶
Initiate MTU exchange with a connected server, using the preferred MTU set using
_IRQ_MTU_EXCHANGEDevent will be raised when MTU exchange completes.
注意： MTU exchange is typically initiated by the central. When using the BlueKitchen stack in the central role, it does not support a remote peripheral initiating the MTU exchange. NimBLE works for both roles.
L2CAP connection-oriented-channels ¶
This feature allows for socket-like data exchange between two BLE devices. Once the devices are connected via GAP, either device can listen for the other to connect on a numeric PSM (Protocol/Service Multiplexer).
注意： This is currently only supported when using the NimBLE stack on STM32 and Unix (not ESP32). Only one L2CAP channel may be active at a given time (i.e. you cannot connect while listening).
Active L2CAP channels are identified by the connection handle that they were established on and a CID (channel ID).
Connection-oriented channels have built-in credit-based flow control. Unlike ATT, where devices negotiate a shared MTU, both the listening and connecting devices each set an independent MTU which limits the maximum amount of outstanding data that the remote device can send before it is fully consumed in
l2cap_listen( psm , mtu , / ) ¶
Start listening for incoming L2CAP channel requests on the specified psm with the local MTU set to mtu .
When a remote device initiates a connection, the
_IRQ_L2CAP_ACCEPTevent will be raised, which gives the listening server a chance to reject the incoming connection (by returning a non-zero integer).
Once the connection is accepted, the
_IRQ_L2CAP_CONNECTevent will be raised, allowing the server to obtain the channel id (CID) and the local and remote MTU.
注意： It is not currently possible to stop listening.
l2cap_connect( conn_handle , psm , mtu , / ) ¶
Connect to a listening peer on the specified psm with local MTU set to mtu .
On successful connection, the the
_IRQ_L2CAP_CONNECTevent will be raised, allowing the client to obtain the CID and the local and remote (peer) MTU.
An unsuccessful connection will raise the
_IRQ_L2CAP_DISCONNECTevent with a non-zero status.
l2cap_disconnect( conn_handle , cid , / ) ¶
Disconnect an active L2CAP channel with the specified conn_handle and cid .
l2cap_send( conn_handle , cid , buf , / ) ¶
Send the specified buf (which must support the buffer protocol) on the L2CAP channel identified by conn_handle and cid .
The specified buffer cannot be larger than the remote (peer) MTU, and no more than twice the size of the local MTU.
This will return
Falseif the channel is now “stalled”, which means that
l2cap_sendmust not be called again until the
_IRQ_L2CAP_SEND_READYevent is received (which will happen when the remote device grants more credits, typically after it has received and processed the data).
l2cap_recvinto( conn_handle , cid , buf , / ) ¶
Receive data from the specified conn_handle and cid into the provided buf (which must support the buffer protocol, e.g. bytearray or memoryview).
Returns the number of bytes read from the channel.
若 buf is None, then returns the number of bytes available.
注意： After receiving the
_IRQ_L2CAP_RECVevent, the application should continue calling
l2cap_recvintountil no more bytes are available in the receive buffer (typically up to the size of the remote (peer) MTU).
Until the receive buffer is empty, the remote device will not be granted more channel credits and will be unable to send any more data.
Pairing and bonding ¶
Pairing allows a connection to be encrypted and authenticated via exchange of secrets (with optional MITM protection via passkey authentication).
Bonding is the process of storing those secrets into non-volatile storage. When bonded, a device is able to resolve a resolvable private address (RPA) from another device based on the stored identity resolving key (IRK). To support bonding, an application must implement the
注意： This is currently only supported when using the NimBLE stack on STM32 and Unix (not ESP32).
gap_pair( conn_handle , / ) ¶
Initiate pairing with the remote device.
Before calling this, ensure that the
bondconfiguration options are set (via
On successful pairing, the
_IRQ_ENCRYPTION_UPDATEevent will be raised.
gap_passkey( conn_handle , action , passkey , / ) ¶
Respond to a
_IRQ_PASSKEY_ACTIONevent for the specified conn_handle and action .
passkey is a numeric value and will depend on on the action (which will depend on what I/O capability has been set):
当 action is
_PASSKEY_ACTION_INPUT, then the application should prompt the user to enter the passkey that is shown on the remote device.
当 action is
_PASSKEY_ACTION_DISPLAY, then the application should generate a random 6-digit passkey and show it to the user.
当 action is
_PASSKEY_ACTION_NUMERIC_COMPARISON, then the application should show the passkey that was provided in the
_IRQ_PASSKEY_ACTIONevent and then respond with either
0(cancel pairing), or