STM32F7508 Discovery Kit Setup Instructions

This topic helps you setup the development environment for STM's STM32F7508 discovery kit.


  • STM32F750N8H6 MCU featuring ARM® Cortex®-M7, 64-KBytes Flash, 340-kbytes RAM
  • 4.3” 480x272 Touch Display
  • 16-Mbit SRAM memory
  • 128-Mbit Quad-SPI Flash memory
  • 128-Mbit SDRAM



Use the Qt online installer to install the following prerequisites. You can download the installer from your Qt account .

  • Qt for MCUs SDK
  • Qt Creator v4.12.4 或更高版本
  • CMake 3.15 或更高版本
  • Ninja 1.10.0 或更高版本

    注意: Ninja is an optional build tool and can be replaced with others like JOM or NMake. It is not needed when using Qt Creator.

  • ARM Toolchain 8-2019-q3-update or IAR Build Tools for Arm V8.50, depending on which toolchain you are using
  • STM32CubeF7 SDK 1.16.0 or newer
  • STM Cube Programmer 2.4.0 or newer

    注意: Ensure that it is installed in the default location ( C:\Program Files\STMicroelectronics\STM32Cube\STM32CubeProgrammer\ ).

注意: The Qt online installer does not install the STM Cube Programmer by default. You must select it explicitly from the list of third-party tools and SDKs.

In addition, flash the bootloader image onto the device. For more information, see Bootloader Flashing Instructions for ST boards .

Qt Creator IDE

  • 发起 Qt Creator 并选择 工具 > 选项 > 设备 > MCU .
  • Select the one of the targets from the drop-down list for Target supported by the Qt for MCUs SDK :
    • Qt for MCUs 1.7 - STM32F7508-DISCOVERY-BAREMETAL 16bpp
    • Qt for MCUs 1.7 - STM32F7508-DISCOVERY-BAREMETAL 32bpp
    • Qt for MCUs 1.7 - STM32F7508-DISCOVERY-FREERTOS 16bpp
    • Qt for MCUs 1.7 - STM32F7508-DISCOVERY-FREERTOS 32bpp
  • Provide the STM32CubeProgrammer install path if it is not installed in the default location.
  • 要求 section, ensure that the platform-specific requirements are met.
  • 选择 Automatically create kits for all available targets on start to create kits automatically.

    注意: You could also manually create/remove kits using Create Kit and Remove Kit .

  • 点击 Apply and restart Qt Creator if you choose to create kits automatically.

注意: Automatically create kits for all available targets on start option is available from Qt Creator v4.14 onwards. On older versions of Qt Creator, you have to explictly create or remove kits using Create kit or Remove kit .


To get started from the command line, ensure that the following these instructions:

  • Qul_DIR to the Qt for MCUs SDK install path.


    • <QT_INSTALL_PATH> is the Qt install directory,
    • and <VERSION> is the directory containing the Qt Quick Ultralite version you are using, for example 1.1.0 .
  • Toolchain install path, depending on which toolchain is being used


    • 对于 IAR 工具链 , set IAR_ARM_COMPILER_DIR to the IAR Build Tools install path.
  • Add the CMake and Ninja tools to your system PATH . If you installed these tools using the Qt online installer, they are installed under <QT_INSTALL_PATH>\Tools .
  • 添加 STM32CubeProg 安装目录到 System PATH 若它未安装在默认位置。
  • Add ST-LINK_gdbserver.exe directory to your System PATH

    其中, <STM32_CUBE_IDE_INSTALL_PATH> is the Cube IDE install path.

    注意: STM32CubeIDE is optional and required only for on-chip debugging purposes.

  • 创建 STM32Cube_FW_F7_SDK_PATH environment variable and set it to the following path:

    其中, <QT_INSTALL_PATH> 是 Qt 安装目录。


Qt Creator provides a build configuration with the kits that you created earlier for the targets. If you are using a command-line setup, configure using the following CMake variables. For more information, see the CMake 手册 .


    The platform to build must be set to stm32f7508-discovery-baremetal for this board.


    此平台支持 armgcc and IAR 工具链。




    The supported color depths by this platform are 16-bit or 32-bit, with 32-bit being the default.

    注意: If this variable is not set, default color depth is used while configuring for the platform.


    By default, the asset data for application is copied to SDRAM on application startup. In order to keep resources in external flash, and not load it to RAM on startup, use the QUL_COPY_TO_RAM CMake option with the value Never when adding assets to the application with qul_add_resource .


The package for STM32F7508-DISCOVERY board comes with the following prebuilt demo binaries

You can find it in the demos_images 目录。

Flashing Instructions for ST boards , for information about flashing the device.

For this board, select N25Q128A_STM32F7508-DISCO as the external loader.

采用预构建 Qt Quick Ultralite 库构建应用程序

Qt Creator IDE

Open the CMake project file for the example you want to build and configure it with the kit you created earlier. Once the project is configured, select 运行 or press Ctrl+r on your keyboard to build and flash the binary to the target.


以下范例构建 watch demo for this board:

cd %Qul_DIR%\demos\watch
mkdir build
cd build
cmake .. -G "Ninja" -DCMAKE_BUILD_TYPE=Release -DCMAKE_TOOLCHAIN_FILE=%Qul_DIR%\lib\cmake\Qul\toolchain\armgcc.cmake -DQUL_PLATFORM=STM32F7508-DISCOVERY-baremetal
cmake --build .

Once you have successfully built the watch demo, you can flash it from the command line:

cmake --build . --target flash_watch

The same procedure applies to any other application.


By default, the output of printf calls are redirected to a virtual serial port, which is exposed on the host machine via USB.


  • Open terminal window and run the following command:
    ST-LINK_gdbserver.exe -cp "<STM32_CUBE_PROG_INSTALL_PATH>\bin"

    其中, <STM32_CUBE_PROG_INSTALL_PATH> is the directory where you've installed the Cube Programmer tool.

    GDB Server is now listening for TCP connections on the default port, 61234 .

    注意: Actual TCP port used by ST-LINK_gdbserver is printed out on gdbserver's console.

  • 运行 arm-none-eabi-gdb in a separate console
    %ARMGCC_DIR%\bin\arm-none-eabi-gdb.exe <PATH_TO>\your_app.elf
  • Connect to the target via the gdbserver in the arm-none-eabi-gdb console using
    (gdb) target remote


ST-LINK_gdbserver requires up-to-date ST-LINK firmware to be installed. If you see the following error:

Error in initializing ST-LINK device. Reason: ST-LINK firmware upgrade required.

you must upgrade the firmware to the latest version using the STM32CubeProgrammer 工具。

If the problem persists after upgrade, retry with ST-LINK Upgrade tool from the ST webpage ( 下载 ).